Aftersales Service

03444 995599

Can’t see your model? Visit our Advice Centre

Dirt is compacted at the base of the dust container

An alarm light will flash on the display to advise you that the dust container is full. Your Synthesis cleaner compacts the dirt, so the container will not require emptying as often as a conventional vacuum cleaner. However it's still good to check and empty the container especially if it has been taken off the product to clean the pre motor filter.

Read more

An alarm light will flash on the display to advise you that the dust container is full. Your Synthesis cleaner compacts the dirt, so the container will not require emptying as often as a conventional vacuum cleaner. However it's still good to check and empty the container especially if it has been taken off the product to clean the pre motor filter.

dust container full indicator

Dust container full indicator

To remove the dust container for emptying start by pressing the release catch at the back of the product. Then take the container to your dustbin and press the catch to release the dust flap and allow the contents to empty into your dustbin. Give it a shake to ensure that all the dirt has emptied out. Also remove any debris tangled around the plunger. Once it has been emptied, press the pin lid shut and refit the container onto the product.

press the release catch to open the flap, make sure the plunger in the centre of the picture is clean and free from any debris

Phone 03446 923 608 and we’ll assess the best resolution for your problem.

Always disconnect your appliance from the mains before you start examining it!

Did you find this useful?

Something went wrong. Please try again.

Thank you!

This solution applies to the following models:

Vacuum Cleaners

Empty after each cleaning cycle

We recommend you empty the dust container after each cleaning cycle, remove the dust box found at the rear of robocom as shown:

Read more

We recommend you empty the dust container after each cleaning cycle, remove the dust box found at the rear of robocom as shown:

Phone 03446 923 608 and we’ll assess the best resolution for your problem.

Always disconnect your appliance from the mains before you start examining it!

Did you find this useful?

Something went wrong. Please try again.

Thank you!

This solution applies to the following models:

Vacuum Cleaners

Empty and clean the dust container

Simply lift the dust container as shown to remove if from the cleaner and take it to your bin. Flip the catch to open the flap and shake the contents out into your bin. We recommend to keep your cleaner working efficiently that it is emptied out when its 2/3 full.

Read more

Simply lift the dust container as shown to remove if from the cleaner and take it to your bin. Flip the catch to open the flap and shake the contents out into your bin. We recommend to keep your cleaner working efficiently that it is emptied out when its 2/3 full.

empty the dust container

lift the container up at a slight angle as shown on the right. The dust container can be washed in warm water but ensure it is fully dry before fitting it back in.

See also filter care

Phone 03446 923 608 and we’ll assess the best resolution for your problem.

Always disconnect your appliance from the mains before you start examining it!

Did you find this useful?

Something went wrong. Please try again.

Thank you!

This solution applies to the following models:

Vacuum Cleaners

Empty when the container is 2/3 full

Check that the dust container is not full, we recommend it is emptied when it is 2/3 full. Simply press the release catch found on the container handle and lift it off. Take it to your dustbin and twist the lid anti clockwise to open the container. You will then be able to lift out the filter and cyclonic unit. Empty the contents into your dustbin. The container, cyclonic unit and filters can be washed in warm water but please make sure they are thoroughly dry before you put everything back together. This may take 24 hours.

Read more

Check that the dust container is not full, we recommend it is emptied when it is 2/3 full. Simply press the release catch found on the container handle and lift it off. Take it to your dustbin and twist the lid anti clockwise to open the container. You will then be able to lift out the filter and cyclonic unit. Empty the contents into your dustbin. The container, cyclonic unit and filters can be washed in warm water but please make sure they are thoroughly dry before you put everything back together. This may take 24 hours.

Phone 03446 923 608 and we’ll assess the best resolution for your problem.

Always disconnect your appliance from the mains before you start examining it!

Did you find this useful?

Something went wrong. Please try again.

Thank you!

This solution applies to the following models:

Vacuum Cleaners

Regularly remove and empty the dust container

To ensure that the robot works efficiently regularly check and empty the dust container.

Read more

To ensure that the robot works efficiently regularly check and empty the dust container.

Phone 03446 923 608 and we’ll assess the best resolution for your problem.

Always disconnect your appliance from the mains before you start examining it!

Did you find this useful?

Something went wrong. Please try again.

Thank you!

This solution applies to the following models:

Vacuum Cleaners