Aftersales Service

03444 995599

Can’t see your model? Visit our Advice Centre

Brush bar care

There is a rotating brush bar fitted underneath the cleaner that sweeps up dirt from the floor. If the bristles become clogged with debris the cleaner will not pick up efficiently. To remove the brush and clean it simply use a flat blade screw driver to turn the lock to the 'open padlock' setting and lift the red catch out. Now pull the brush out and carefully remove any debris tangled around the bristles. Re fit and place the securing catch back in place and lock it by turning the catch to the 'locked padlock' setting.

Read more

There is a rotating brush bar fitted underneath the cleaner that sweeps up dirt from the floor. If the bristles become clogged with debris the cleaner will not pick up efficiently. To remove the brush and clean it simply use a flat blade screw driver to turn the lock to the 'open padlock' setting and lift the red catch out. Now pull the brush out and carefully remove any debris tangled around the bristles. Re fit and place the securing catch back in place and lock it by turning the catch to the 'locked padlock' setting.


For best results we advise that you replace the brush bar once per year or if the brushes look worn or the bristles have fallen out. New brushes can be purchased from the spares section of our website.


Please note there is not a belt fitted to this product

removing the brush bar

Phone 03446 923 608 and we’ll assess the best resolution for your problem.

Always disconnect your appliance from the mains before you start examining it!

Did you find this useful?

Something went wrong. Please try again.

Thank you!

This solution applies to the following models:

Vacuum Cleaners

Check the brush bar is clean

To keep your cleaner working efficiently regularly tip the cleaner over and look at the brush bars. If any debris is tangled round them the cleaner will not pick up effectively. To remove the brush remove the retainer by unscrewing it with a standard Phillips screwdriver:

Read more

To keep your cleaner working efficiently regularly tip the cleaner over and look at the brush bars. If any debris is tangled round them the cleaner will not pick up effectively. To remove the brush remove the retainer by unscrewing it with a standard Phillips screwdriver:

the brushes will now lift out for cleaning

Phone 03446 923 608 and we’ll assess the best resolution for your problem.

Always disconnect your appliance from the mains before you start examining it!

Did you find this useful?

Something went wrong. Please try again.

Thank you!

This solution applies to the following models:

Vacuum Cleaners

Remove and clean the brush

There is a brush roll in the main cleaning head which spins round sweeping your floors. It is possible that hair, threads and debris may get tangled around the brush and stop it working efficiently. Regular checks should be made and its easy to remove the brush for cleaning. Simply turn the brush head over and slide outwards the retaining bar as shown.

Average rating:

Read more

There is a brush roll in the main cleaning head which spins round sweeping your floors. It is possible that hair, threads and debris may get tangled around the brush and stop it working efficiently. Regular checks should be made and its easy to remove the brush for cleaning. Simply turn the brush head over and slide outwards the retaining bar as shown.

Now lift the brush out at an angle as shown here

Pick off any hair or debris you may find tangled around the bristles, also clean away any obstructions in the body of the brush head. Brushes do wear over time and we recommend you fit new brushes once per year to keep your cleaner working efficiently. You can purchase your replacement brushes from the spares section of our website.

Phone 03446 923 608 and we’ll assess the best resolution for your problem.

Always disconnect your appliance from the mains before you start examining it!

Average rating:

Did you find this useful?

Something went wrong. Please try again.

Thank you!

This solution applies to the following models:

Vacuum Cleaners

Remove any debris tangled around the brush

The brush roll should be regularly cleaned of visible hair, dust and other debris. The brush can usually be removed and manually cleaned. Brushes do wear and Hoover recommend that the brushes are replaced once per year to keep your cleaner working efficiently. Replacement brushes can be purchased from the spares section of the website.

Average rating:

Read more

The brush roll should be regularly cleaned of visible hair, dust and other debris. The brush can usually be removed and manually cleaned. Brushes do wear and Hoover recommend that the brushes are replaced once per year to keep your cleaner working efficiently. Replacement brushes can be purchased from the spares section of the website.

Removing the brush is easy but dependant on which model design you have. On some models the brush release is found next to the brush as shown, use a flat blade screwdriver to unlock the release bar which can then be lifted out.

 

removing the locking bar

On some models the brush release clip is found on the side of the product, unclip as shown and the brush can then be lifted out.

unclip the brush release

With the brush removed any threads or debris tangled around the bristles can be removed

brush roll released from the cleaner

Phone 03446 923 608 and we’ll assess the best resolution for your problem.

Always disconnect your appliance from the mains before you start examining it!

Average rating:

Did you find this useful?

Something went wrong. Please try again.

Thank you!

This solution applies to the following models:

Vacuum Cleaners

The brush can be removed and cleaned

Regularly have a look at the brush roll in the foot of the cleaner. It will work much better if it is clean and rotating freely. Remove any hair and thread trapped around the brush. There is no belt in this product.

Read more

Regularly have a look at the brush roll in the foot of the cleaner. It will work much better if it is clean and rotating freely. Remove any hair and thread trapped around the brush. There is no belt in this product.

Use a flat blade screwdriver to twist the locking peg to the 'open' padlock symbol. The securing bar can now be removed and the brush roll taken out and cleaned.

brush removed for cleaning

Brush roll removed for cleaning for best results fit a new one once per year

Phone 03446 923 608 and we’ll assess the best resolution for your problem.

Always disconnect your appliance from the mains before you start examining it!

Did you find this useful?

Something went wrong. Please try again.

Thank you!

This solution applies to the following models:

Vacuum Cleaners